Design Graphics Engineering Technology

ASSOCIATE OF APPLIED SCIENCE DEGREE (AAS)

ťGrade Requirements: A grade of C or better in all DGET courses (a grade of "C-" is not acceptable) in addition to an overall GPA for all courses of 2.00 or higher.

ť Credit Hour Requirements: 63 total hours are required -- 24 of which are required within the Design Graphics Engineering Technology AAS program.

ť Assessment Requirements: Students will be required to complete certain assessment instruments as part of the overall requirements for receiving their associate's degree. Please see your advisor or your department for specific information regarding assessment.

Advisement

All Design Graphics Engineering Technology students are required to meet with a faculty advisor at least annually for course and program advisement. Call 801-626-6305 for more information or to schedule an appointment. Advisement may also be obtained in Engineering Technology, room 214.

Admission Requirements

Declare your program of study. There are no special admission or application requirements for this program.

General Education

Refer to General Requirements for Associate of Applied Science requirements. Computer and Information Literacy as defined in this catalog is also required for the AAS degree.

Course Requirements for AAS Degree

Design Graphics Engineering Technology Courses Required (24 credit hours)

DGET 1060 Fundamentals of Drafting Using 3D CAD (3)
DGET 1160 Documentation Using 3D CAD (3)
DGET 1360 Fundamentals of Architectural Drafting Using CAD (5)
DGET 2350 Advanced Architectural Drafting (4)
DGET 2460 Design Fundamentals Using 3D CAD (3)
DGET 2650 Advanced Mechanical Drafting and Design (3)
DGET 2660 Structural Detailing (3)
DGET 2899 Associate's Degree Assessment (0)

Technical Courses Required (9 credit hours)

MFET 1210 Machining Principles Lecture/Lab I (3)
MFET 2360 Manufacturing Processes and Materials (3)
MFET 2410 Quality Assurance and Improvement (3)

Technical Electives (2 credit hours minimum)

A minimum of 2 credit hours of technical electives chosen from the following list or approved by the program coordinator are required.

CEET 1110 Basic Electronics (2)
MFET 2150/2150L Metal Forming, Casting and Welding (4)
MFET 2440/2440L Computer Numeric Control (CNC) in Manufacturing (3)
MFET 2670/2670L GMA, FCA and GTA Welding (3)
CMT 1210 Residential Construction Materials and Methods (3)
CMT 1500 Computer Applications in Construction (2)
CMT 2220 Construction Contracts and Specifications (3)
CMT 2340 Construction Surveying (2)
CMT 2360 Building Codes and Inspection (2)

Support Courses Required (22 credit hours)

ENGL EN1010 Introductory College Writing (3)
ENGL EN2010 Intermediate College Writing (3)
COMM HU2110 Interpersonal & Small Group Communication (3)
MATH QL1080 Pre-Calculus (5)
or MATH QL1050 College Algebra (4)
& MATH 1060 Trigonometry (3)
PHYS PS/SI2010 College Physics I with lab (5)
TBE TE1700 Intro to Microcomputer Applications (3)

Suggested Course Sequence

The following suggested course sequence is provided to assist students in planning their schedules. Use this only as a guideline and be sure to consult with an advisor.

Freshman Fall		Freshman Spring
DGET 1060	3	DGET 1160	3
ENGL EN1010	3	DGET 1360	5
MFET 1210	3	ENGL EN2010	3
MATH QL1080	5	TBE TE1700	3
		Creative Arts Elective	3
Total Hours	14	Total Hours	17

Sophomore Fall		Sophomore Spring
DGET 2350	4	DGET 2650	3
DGET 2460	3	DGET 2660	3
MFET 2410	3	SS Elective	3
MFET 2360	3	PHYS PS/SI2010 + L	5
COMM HU2110	3	Lower Division Elective	2
		DGET 2899	0
Total Hours	16	Total Hours	16

Weber State University 2007-2008 Catalog